ServicesPool Repair
Pool Repair in Florence
When a pump hums but won't start, a filter gauge climbs or a heater clicks and quits, we find the actual failed part before we recommend anything. You hear what broke, why it broke and what fixing it involves, in plain terms.
Find the failed part, then fix that part
Pool repair covers the equipment pad and the plumbing that feeds it: pumps and motors, filters, multiport and diverter valves, heaters, salt cells, timers and the PVC runs between them. Most failures trace back to a handful of causes. Heat breaks down motor capacitors and bearings, hard water scales heat exchangers and salt cells, and debris chews up impellers and O-rings.
We start by testing, not guessing. A pump that won't prime might need a new lid O-ring, a cleared impeller or a full motor, and those are very different bills. We check each possibility in order, show you what we found and then give you the repair options. We are ROC licensed, and every repair is completed in-house by our own techs, not handed off to a subcontractor.
What our repair work covers
Pump and motor repair
We replace start and run capacitors, worn bearings, shaft seals and cracked impellers. If the motor windings are burned out, we tell you whether a motor swap or a full pump replacement makes more sense for your setup.
Filter and valve repair
Cracked multiport spider gaskets, broken handles, stripped filter tank clamps and failed pressure gauges are common. A worn spider gasket lets water bypass the filter media, so the pool clouds even while the pump runs.
Heater diagnosis
We work through ignitors, flame sensors, pressure switches and thermal fuses, and check the heat exchanger for scale. Scale makes the exchanger overheat and trip its safety limits.
Salt cell and control issues
We inspect cells for calcium buildup and test output and flow sensors before calling a cell dead. Sometimes a cleaning or a sensor is the fix, not a new cell.
Plumbing at the pad
We cut out and replace cracked PVC fittings, failed unions and sun-brittle pipe above ground, and reseat valves that weep at the threads.
Signs your pool equipment needs repair
The pump hums but won't spin
A humming motor that doesn't turn usually points to a failed capacitor or a seized bearing. Leaving it powered in that state can burn out the windings.
Filter pressure keeps climbing
If the gauge reads well above its clean baseline right after a cleaning, something downstream is restricted or the gauge itself has failed.
Air bubbles in the pump basket
Air on the suction side often comes from a dry lid O-ring, a loose union or a cracked fitting. The pump loses prime and runs hot.
Water around the pump
A drip from between the motor and the pump housing is typically a worn shaft seal. Water that reaches the motor bearings shortens their life quickly.
Heater lights, then shuts off
Short cycling usually means low flow, a dirty flame sensor or a tripped pressure switch. Each has a different fix, so we test before replacing parts.
Grinding or screeching noises
Bearing noise gets worse under summer load, when pumps run long hours in 110-degree heat. Catching it early often means a bearing job instead of a new motor.
How a repair visit runs
- 1
You describe the problem by phone
Tell us what you're seeing and hearing, plus the equipment brand if you know it. We set a visit and give you a free quote once we've seen the pad.
- 2
We test the equipment
We check voltage at the motor, capacitor readings, filter pressure, flow and every seal and fitting on the suction and return sides. We note what's worn as well as what has failed.
- 3
You get plain findings and options
We show you the failed part and explain why it failed. If a repair and a replacement are both reasonable, we lay out both so you can choose.
- 4
We make the repair and confirm it
Our tech completes the work, primes the system and runs it while watching pressure and flow. We clean up the pad area before we leave.
What affects the cost of a pool repair
Repair cost depends mostly on which part failed and how hard it is to reach. We don't quote a number until we've tested the equipment, because the same symptom can come from a small part or a large one. Your quote lists the parts and labor separately.
- The failed component
- A capacitor or O-ring costs far less than a motor, heat exchanger or salt cell. Testing first keeps you from paying for parts you didn't need.
- Equipment age and parts availability
- Older or discontinued models can need adapter fittings or harder-to-find parts. Sometimes that tips the decision toward replacement.
- Plumbing changes
- If a new part doesn't match the existing pipe layout, we have to replumb, which adds fittings and labor time.
- Related wear we find
- A failed shaft seal can damage bearings if it went unnoticed. We tell you about secondary damage up front so the quote reflects the full job.
Pool repair questions
Something not covered here? (520) 645-8108
Should I repair my pump or replace it?
It depends on what failed and how old the pump is. Seals, capacitors and impellers are usually worth repairing. A motor with burned windings on an older pump often costs nearly as much to fix as a new, more efficient pump. We give you both numbers and our honest read.
Do you send a subcontractor for repairs?
No. All repairs are completed in-house by our own techs. The person who diagnoses your equipment is part of the same crew that fixes it, so nothing gets lost between the inspection and the repair.
What should I check before I call?
Look at the breaker and the timer or automation settings, since a tripped breaker or a shifted schedule can look like a dead pump. Check that the water level sits at mid-skimmer and the pump basket isn't packed with debris. If the problem is still there, note any sounds or gauge readings and we'll start from those.
Why does my pump keep losing prime?
Usually air is getting in on the suction side. Common causes are a dry or cracked lid O-ring, a loose union, a cracked fitting or a low water level that lets the skimmer draw air. We check them in order and fix the one that's actually letting air in.
Can I keep running the pool until you arrive?
If the motor is humming without spinning, turn it off at the breaker to protect the windings. If there's a small drip at the shaft seal, short run times are usually fine. Describe what's happening when you call and we'll tell you what's safe.
Do you work outside Florence?
Yes. We handle pool repair in Florence and nearby towns including San Tan Valley, Coolidge, Queen Creek and Casa Grande. Ask when you call and we'll confirm your area.
Find out what actually failed
Tell us what your equipment is doing and we'll schedule a visit to test it. You get a clear diagnosis and a free quote before any work starts.